









EN-49248 6706 Fuel Injector Rail Assembly Remover Tool & GM245 Fuel Injector Seals Tools EN-49245,EN-51105 For GM Engines
24.68$
12.59$
Quantity:
1
Availability:
Limited StockColor
Delivery estimate
Delivery:
Nov 28 – Dec 4 to United States
1.99$ shippingTrackedImport duties may applyEN-49248 6706 Fuel Injector Rail Assembly Remover Tool & GM245 Fuel Injector Seals Tools EN-49245,EN-51105 For GM Engines
GM245 Fuel Injector Seals Tools
Application:
OE Replace Part: #EN-49245, #EN-51105 and #18683AA000.
Fits for Holden Colorado 7 [2016]
Fits for Subaru 2.0L 2.4L turbo engines [2014-2019]
Fits for General Motors 2.0L 3.6L engines with Hitachi fuel injectors [2010-2017]
Fits for GM 2.0L 2.5L 5.3L 6.2L engines with Bosch, Continental Delphi fuel injectors [2012-2017]
Function:
Made of high quality iron. Durable, Anti-Corrosion, Providing effective wear resistance and aging resistance, and will not wear and leak over time.
Used for replacing the fuel injector teflon seals. This tool set helps install the seal on the injector for leak-free operation.
For the Hitachi Sidi System used for 2010-later LF1 3.6L V6 and for LAF 2.0L Ecotec has 2 seals in the tip of the injector. These seals must be installed into their grooves, and then sized to the engineered dimension before the injectors are installed into their bores in the cylinder head.
EN-49245 includes two seal installation pilots (one for each groove), allows the seal to slide onto the injector tip without catching on any machined surface or the incorrect groove.
EN-49245 also includes a seal installer to drive the seal over the pilot and into the groove, and a sizer to compress each seal into its groove and ensure its size prior to installation.
EN-49245 must be used to install the seals correctly and to ensure they are sized correctly for leak-free operation.
Warm Tips: 2013-newer injectors for Bosch, Continental and Delphi feature slightly larger injector tips, and require the protector ramps from EN-51105 Injector Seal Installer Adapter set. These are used with the installer and sizer from EN-49245.
Installation Steps Tips:
1. Cut off the old Teflon seal near the tip of the injector.
2. Place the seal installer guide(pilot cone) on the tip of the injector.
3. Push the new seal on the installer guide(pilot cone).
4. Use the seal installer to push the seal into the groove of the injector.
5. Use the seal sizer tool to compress the Teflon seal to the correct size.
6. Done! (Kindly Noted: EN-49245 must be used to install the seal correctly and ensure that its size is correct.)
EN-49248 Fuel Injector Rail Assembly Remover Tool
Applications:
OEM:EN-49248; 6706
Fits for 2007 - 2014 General Motors Cadillac Saturn Pontiac Chevrolet direct injection engines.
For 4.3L 3.6L 3.0L GDI V6,For 2.5L 2.4L 2.0L GDI I-4.
Note: If you are working on a 5.3L or 6.2L you will need a quantity of 2 sets.
Features:
[Prevent Damage]:Design to remove the direct injection fuel rail without damage. The injector and rail assembly must be removed as straight as possible to prevent damaging an injector bore in the cylinder head or the rail mount assembly.
[High Quality]:Made of highest quality Steel for great strength, prevent corrosion and rust, impact resistance, sturdy and durable. High precision and hardness ensure reliable long-term service
[Easy to Use]:This EN-49248 installs in place of the mounting bolts, and reaches under the injector rail near each mount location.The hand wheels on EN-49248 at each mount location are tightened evenly to un-seat all injectors evenly.
Installation Steps Tips:
Step 1:
Remove the fuel injection fuel rail noise shield.
Disconnect the electrical harness from the fuel rail harness connection.
Disconnect all 4-fuel injector electrical connections.
Remove the fuel rail assembly retaining bolts.
Note: Use care to avoid contact with the fuel rail harness during special tool installation and fuel rail removal.
Step 2:
Install EN-49248studs (1) into the 2 center fuel rail assembly retaining bolt locations.Tighten the studs to 22-Y(16-lb-ft).
Install EN-49248 remover-(2) onto each stud, and engage the hooks to the fuel rail.
Install the nuts-(3) retaining there mover onto the studs and tighten until snug.
Step 3:
Note: EN-49248 will assist in the proper removal of the fuel rail assembly. Ensure that the following conditions are met:
Turn the handles simultaneously in order to pull the fuel rail straight out along the fuel injector axis.
DO NOT twist when pulling out on the fuel rail and injector assembly.
Using EN-49248 remover, remove the fuel rail assembly-(1).
Package Included:
1SET EN-49248 Fuel Injector Rail Assembly Remover Tool & GM245 Fuel Injector Seals Tools








Specifications
- Origin
- Mainland China
- Special Features
- Fuel Injector Rail Assembly Remover Tool+ Fuel Injector Seals Tools
- Country/Region of Manufacture
- China
- Manufacturer Part Number
- XLB-1179+XLB-1180-BK
- OEM NO.
- EN-49245, EN-51105, 18683AA00
- Other Part Number
- EN-49248, 6706
- Choice
- yes
Customer Reviews
13 ratings
good value for price (2)
accurate description (1)
fast delivery (1)
works fine (1)
excellent build quality (1)
requires external tools (1)
Customer photos (1)
Buyer from Saudi Arabia
October 23, 2026
Variant: Color:6706
its great and work fine but it will be much better if its harder materials
Buyer from Greece
July 24, 2026
Variant: Color:6706
Good
Buyer from Colombia
April 10, 2026
Variant: Color:GM245
good product, good quality
Buyer from Peru
February 19, 2026
Variant: Color:GM245
Very good tool, fast delivery of the product
Buyer from Kuwait
February 3, 2026
Variant: Color:6706
Good product, but there are cases where it cannot be opened without external tools.
m***g
December 26, 2025
Variant: Color:6706
Same description Worth the price
EN-49248 6706 Fuel Injector Rail Assembly Remover Tool & GM245 Fuel Injector Seals Tools EN-49245,EN-51105 For GM Engines
24.68$
12.59$
Quantity:
1
Availability:
Limited StockColor
Delivery estimate
Delivery:
Nov 28 – Dec 4 to United States
1.99$ shippingTrackedImport duties may apply






