









Touchless Soap Dispenser Automatic Sensor Foam Type-C Charging Smart Induction Hand Washer with Temperature Digital Display
61.54$
28.31$
Quantity:
1
Availability:
Limited StockColor
Delivery estimate
Delivery:
Nov 26 – Dec 2 to United States
1.99$ shippingTrackedImport duties may applyPlease Read below Usage notes before use:
1. Remove the protective film on the touch screen, or perform this step as needed.
2. Charging time is about 1-2 hours.
3. When installing the machine, ensure that it is at least 20 centimeters away from the desktop (if the distance is too close, the infrared sensor head may be affected by reflections from the tabletop or mirror, causing automatic liquid dispensing)
4. The wall surface where the machine is to be installed needs to be wiped clean with a dry cloth; after being fixed with double-sided tape, glue should be applied to the edges of each hook for reinforcement
5. Press and hold the power button to turn on the device. For specific instructions and the mixing ratio of foam hand sanitizer, please refer to the instruction manual
6. The entire machine is not waterproof, so please do not directly flush the body with water
7. Shake the liquid soap and water evenly (with a ratio of 1 part liquid soap to 4 parts water), dilute with clean water, and then pour it in.
Solution for situations where the motor fails to operate due to "too low temperature" or "too viscous soap solution": Press the power button three times in succession to activate the cleaning mode and force the machine to operate (power on/dispense liquid)

Three-speed adjustable + changeable liquid automatic soap dispenser
Different cleaning liquids can be replaced, and the bubble volume can be adjusted in three levels, which can meet the needs of different people
So you can adjust it to fit your needs. It also comes with a top-notch infrared sensor that can handle even the brightest light - just make sure to install it at the right distance.(Install it 0.65ft/20cm away from your table)


Installation Method
1.Clean the wall with a rag
2.Tear off the adhesive and paste it on the wall, let it stand for more than 24 hours
3.Buckle the machine on the adhesive
4.Read the user manual
5.Start the machine
Wall-Mounted Automatic Soap Dispenser
Every product is built with heart
Specification: 5.1in/13cm x 2.5 in/6.2cm
Maximum capacity: 300ml/12oz
Battery capacity: 2000
Product weight: 260g/0.57lb
Waterproof level: IPX5
Installation method: strong non-marking glue wall-mounted

0.25s extremely fast foaming, no need to wait

Nano-level volumizing foam

IPX5 level waterproof

300 ml Large capacity

Steps to install the soap dispenser on the wall

Punch-free strong and non-marking glue, easy to use

Frequently Asked Questions
Q: How should hand soap be added?
A: If it is a foam hand soap, you can pour it directly without adding water
A: If it is an ordinary hand soap, please add the hand soap first, and then add water. The most appropriate ratio is 1 hand soap : 3 water, which can be adjusted according to the desired bubble concentration.Can't use a soap with particles, such as starlight hand soap, fluorescent hand soap, etc., particles can cause blockage
Q: The soap dispenser works, but no bubbles come out?
A: The initial judgment is that the outlet is blocked. The solution is to add warm water and adjust it to the highest level for repeated induction and dredging.

TROUBLESHOOTING GUIDES!
1.Not enough bubbles? Generally, this is caused by insufficient amount of ordinary hand soap. We recommend that the ratio of ordinary hand soap to water is 1:3, and the amount of hand soap should be more than less. Shake well before turning it on.
2.You can feel it when you stretch your hand over, but no bubbles come out? Only a small amount of liquid comes out? Probably due to the blockage of the outlet, the hand soap was not shaken evenly when adding the liquid, which caused the hand soap to precipitate, or the ordinary hand soap was directly added to cause blockage. It is recommended to add warm water and adjust to the highest level for repeated induction.
3.The product you are browsing now is a foam type. If you add foam soap, you can add it directly. If you choose ordinary gel soap, please dilute it with a ratio of 1 soap: 3 water before adding it.
4.No response to charging? Due to the fact that the product is sometimes turned on during transportation, the battery is completely drained. After receiving the product, please continue to charge it for 1.5-2 hours, and then use it after it is fully charged.
5.No reach sensor, but the soap dispenser foams by itself? We recommend that the machine be installed at a distance of more than 20cm from the countertop to prevent false induction caused by reflections on the countertop.
6.Can't use a soap with particles, such as starlight hand soap, fluorescent hand soap, etc., particles can cause blockage.
7.Black sponge cannot sense (because black sponge absorbs infrared rays, black sponge cannot be used for sensing)
8.We support after-sales service for one year, if your return window has been closed, please take the initiative to inform us, we will solve the problem for you, thank you for your support.
From the brand

Specifications
- Brand
- CREAROMA
- Voltage
- <20V
- Origin
- Mainland China
- Certification
- CE
- Choice
- yes
Customer Reviews
1 rating
Touchless Soap Dispenser Automatic Sensor Foam Type-C Charging Smart Induction Hand Washer with Temperature Digital Display
61.54$
28.31$
Quantity:
1
Availability:
Limited StockColor
Delivery estimate
Delivery:
Nov 26 – Dec 2 to United States
1.99$ shippingTrackedImport duties may apply






