







DC 5V-30V Dual MOS Time Delay Relay High Level Trigger LED Digital Display Cycle Time Timer Delay Switch Circuit 12V 24V 0-999
11.34$
6.35$
Quantity:
1
Availability:
100+In StockSize
Delivery estimate
Delivery:
Delivery estimate shown at checkout
Module features and usage:
1. Realize high frequency, fast and frequent on-off of the circuit, and Sukima Switch times;
2. The on-off process will not generate noise, no electric sparks, and no electromagnetic interference;
3. The service life is longer than that of commonly used electromagnetic relays;
4. Adopting dual MOS parallel active output, lower internal resistance, higher current, strong power, 10A at room temperature, 400W, meeting the needs of most devices;
5. It is often used to control motors, light bulbs, LED light strips, DC motors, micro water pumps, solenoid valves, etc. Through this module, these devices can be easily controlled, which is very convenient.
Module highlights:
1. Wide voltage operation (5-36V), most devices can be used, very convenient;
2. The interface is clear and simple, powerful, and easy to understand, almost meeting all your needs;
3. It has a one button emergency stop function (STOP key) with reverse connection protection, and reverse connection does not burn;
4. Added a sleep mode, which automatically turns off the display after enabling it without any operation for 5 minutes;
Wake up with any button;
5. Different OP, CL, and LOP parameters can be set, which are independent of each other and saved separately;
6. All set parameters are automatically saved after power off.
Working mode:
P1 mode: After the signal is triggered, the relay conducts for OP time and then disconnects; During the OP time, proceed as follows
P1.1: Signal triggered again invalid
P1.2: Signal triggered again for re timing
P1.3: The signal triggers a reset again, the relay is disconnected, and the timing stops;
P-2: Give a trigger signal, after the relay is disconnected for CL time, the relay conducts for OP time, and after the timing is completed, disconnect the relay;
P3.1: After the trigger signal is given and the relay is turned on for OP time, the relay will disconnect for CL time, and then the above actions will be repeated. If the signal is given again during the cycle, the relay will disconnect and stop timing; The number of cycles (LOP) can be set;
P3.2: After powering on, there is no need to trigger the signal. The relay conducts OP time, and the relay disconnects CL time. Cycle the above actions; The number of cycles (LOP) can be set;
P-4: Signal holding function: If there is a trigger signal, the timer will be reset and the relay will remain conductive; When the signal disappears, time OP and disconnect the relay; During the timing period, if there is another signal, the timing will be reset to zero;
Product parameters:
1: Working voltage: DC 5V -36V;
2: Trigger signal source: High level trigger (DC 3.0V-24V) The signal ground is not in common with the system ground to improve the system's anti-interference ability (it can also be short circuited to common ground)
3: Output capacity: DC 5V-36V, continuous current 15A at room temperature, power 400W! Under auxiliary heat dissipation conditions, the maximum current can reach 30A.
4: Quiescent current: 15mA
5: Service life: unlimited switching times; Working temperature: -40-85 ℃; Size: 6.0 * 3.4 * 1.2cm
6: Equipped with optocoupler isolation, enhanced anti-interference ability, industrial grade circuit board, set parameters for permanent memory after power outage.
Parameter Description:
OP conduction time, CL disconnection time, number of LOP cycles (1-999, "---" represents infinite cycles)
These parameters are independent of each other, but each mode shares these parameters. For example, if the conduction time OP is set to 5 seconds in P1.1 and the user wants to switch to P1.2 mode, when entering P1.2 to set the corresponding parameters, the OP will also be 5 seconds;
Short press SET key on Home screen (display 000), OP (CL, LOP) and corresponding time XXX will be displayed;
If there is only OP time in the mode (such as mode P1.1, P1.2, P1.3), short pressing the SET key will only display OP and the corresponding time;
If there are OP, CL, and LOP in the mode (such as modes P3.1 and P3.2), pressing the SET key briefly will display OP and corresponding time, CL and corresponding time, LOP and corresponding times;
After setting the mode, you can easily view the parameters set in the current mode by pressing the SET key briefly on the Home screen, which is very convenient!
How to set parameters:
Firstly, determine the working mode of the relay;
2. According to the operating mode of the relay, on the Home screen (when the module is powered on, it will flash under the current operating mode (default P1.1 mode), and then enter the Home screen,) "Long press the SET key for 2 seconds, then release" to enter the mode selection interface, and select the mode to be set (P1.1~P-4) by short pressing the UP and DOWN keys;
3. After selecting the mode to be set (such as P3.2), press the SET key briefly to set the corresponding parameters. At this time, the parameters to be set will flash (OP conduction time, CL disconnection time, number of LOP cycles ("-" represents infinite cycles)). Adjust the parameter values through UP and DOWN, and support long press (fast increase or decrease) and short press (increase or decrease by 1 unit); After setting the parameter value, press the STOP key briefly to select the Decimal separator position, and select the timing range (corresponding time 0.1 seconds~999 minutes); Short press the SET key to set the next parameter for the current mode, the process is the same as above;
4. After setting the parameters of the selected mode, long press the SET key for 2 seconds and then release it. The currently set mode will flash, and then return to the Home screen. The parameters are set successfully, very simple!
Home screen: "000" (no Decimal separator) is displayed when the relay is not working, and Decimal separator is displayed when the relay is working, which is very clear!
Mode selection interface: long press SET key to enter. After setting, long press SET key to exit and return to the Home screen, which is very simple!
STOP button function extension:
Relay Enable Mode:
1. ON: The relay is allowed to conduct during the OP conduction time;
2. OFF: The relay is prohibited from conducting and always in a closed state;
Short press the STOP key on the Home screen to switch between ON and OFF, the current status will flash, and then return to the Home screen. (This function is an emergency stop function, which opens and closes the relay with one click)
Sleep mode:
1. C-P sleep mode: without any operation within five minutes, the Nixie tube automatically turns off the display and the program runs normally;
2. O-d normal mode: Nixie tube is always on display;
Press and hold the STOP button for 2 seconds, and then release it to switch between C-P and O-d states. The current state will flash, and then return to the Home screen.
Product List
1 * Control board









Specifications
- Brand
- occkic
- Origin
- Mainland China
- EU LVD Voltage
- Low voltage: Below 50Vac or 75Vdc
- Power Source
- Ac, DC
- Applicable Object
- Other
- Theory
- Time Relay
- Voltage
- 24V
- Model Number
- DDC-432
Customer Reviews
106 ratings
works well (8)
fast delivery (5)
excellent quality (5)
satisfied (5)
recommended (5)
arrived undamaged (3)
Customer photos (12)
V***y
December 16, 2025
Variant: Size:Relay and Case
thank you
F***e
October 25, 2026
Variant: Size:Relay and Case
A very nice little programmable timer module, instructions as to how to program on YouTube, very versatile has many modes. The output switching is on the low side, probably has an N channel FET providing the switch output. I am going to buy more in the not too distant future. The picture shows the current dawn in my circuit which is a 12 V relay available from AliExpress and also it is counting down as an eight minute timer with one second resolution.
Buyer from Algeria
October 24, 2026
Variant: Size:Relay and Case
Received. but no manual to use it! I would like to have it. Thank you
Buyer from Brazil
September 30, 2026
Variant: Size:Relay and Case
Product of excellent quality.
Buyer from Brazil
September 15, 2026
Variant: Size:Relay and Case
All good, just need to test it.
Buyer from Brazil
August 19, 2026
Variant: Size:Relay and Case
Order received on time, everything seems fine, I will test it later.
DC 5V-30V Dual MOS Time Delay Relay High Level Trigger LED Digital Display Cycle Time Timer Delay Switch Circuit 12V 24V 0-999
11.34$
6.35$
Quantity:
1
Availability:
100+In StockSize
Delivery estimate
Delivery:
Delivery estimate shown at checkout







